How to Build a Funny Bird House

Miesel Creature Birdhouse
Miesel Creature Birdhouse

I bought these plans from Meisel and thought I would review building this funny birdhouse. My bird house is called “City Beatnik” and there are two different plans included for $15. They have many “old man” type plans. Even more animals. These are full size drawings.  Here is a book by the same designer on Amazon, but they are not full size drawings except for the smaller parts.

IMG_1401
Plans Funny Face Birdhouse
IMG_1403

I found the full size plans useful and they include a cutting guide to get the most from your wood. It can be cut from a 1″x 10″x 8′ piece of pine or cedar. I used rough-cut reclaimed lumber, which caused me a bunch of headaches, because it was cupped. I did like the rough surface.

Let me first say  I use power tools that I have acquired over the years. I understand that many do not have the room or money for these. I think this birdhouse can be built using a jigsaw. With it use a straight edge and a protractor to set the angle of the blade for the bevel cuts. Sandpaper, glue, nails and a way to bore the 1 1/4″ hole and you are set. It would great to build with a kid . I still remember building a birdhouse with my grandfather and that was long ago.

I started by cutting all my pieces to the correct length. Using a crosscut sled I made for my table saw made this easier. Remember to cut to the waste side. Then cut to width. Theses are your blanks to cut the required angles and bevels on. I used my miter gauge to cut the angles for the end pieces. I actually cut the first end, then traced it on the second blank, cut it on the band saw to save time. Since I made mine out of reclaimed lumber and had to glue two pieces together to get the width, I needed to keep the seam centered so it looked right. This made it more difficult.

IMG_1407
Cutting Birdhouse Roof
IMG_1408

To cut the bevels on the sides, I set the bevel on my saw and used the sliding mitre gauge with an extended wood fence to get the piece close to the gauge while keeping my hand far away. Since the piece was already the correct length, I gradually cut the bevel with repeated passes until the bevel was completed.IMG_1431IMG_1429

IMG_1433

I found it easiest to work directly off the main drawing. I got a bit confused how they     measured the angles, so I just used a protractor to measure them.
IMG_1432

Assemble the sides and ends. I used 18 gauge nails and glue. Titebond II is weather resistant. As you can see my sides are cupped. Custom fit the bottom. If you are going to actually use it for birds to live in, then you need to be able to remove the bottom to clean out the old nests. I put a screw in each side to hold it in place. In the picture, the bottom is square, the sides are not. Drill the hole next.

IMG_1438
IMG_1439
IMG_1441

Next comes the part that makes this more than just an ordinary birdhouse–adding the face. I had read about using Glad Press’n Seal to transfer patterns to wood and gave it a try. It worked great! Posted about it here. Using a scroll saw, I cut out the pieces, sanding them smooth on a 1 inch belt sander.

Transferring image with PressnSeal
IMG_1448
IMG_1449

After I had all the parts cut, I rounded the edges slightly. I used a 1/4″ router bit to round over the nose. Looking back, I wish I had rounded it over more. A file and sandpaper can get the same results. Now it is time to attach the face. I had an uneven surface to attach the pieces to. I glued the nostrils and the bottom of the eyes to the nose first. I actually drilled two holes and used screws and glue to attach the nose. I worked from inside the house using a stubby screwdriver. If you have a smooth surface, the screws probably are not necessary. Attach the rest of the parts as in the plans. I didn’t use the ears, because I did not like them.

IMG_1453
Attaching face to bird house

After the glue has set, attach the roof. I found it easier to join the two roof pieces before putting them on the house. Lastly, attach the two acrylic eyeballs. These you have to buy from Meisel when you buy the plans.

IMG_1447
Funny Face Birdhouse

In the end I am pleased with the results. The plans include a second birdhouse. I will make that one too, using new wood, saving me a lot of headaches.

Hope this has been helpful. Please post comments below. Especially if you have built a character birdhouse.

How to Make a Wooden Hat Stand

Straw Hat on Stand

DIY Wooden Hat StandYou can make a wooden hat stand easily. I was asked to make hat stands out of wood as a Christmas present. They were to be made different heights so they could be put on a closet shelf. Hats with brims could be put closer together as the brims would not touch each other, because they are at different heights.

Simply made out of 15mm (9/16″) baltic birch ply. 2 disks- 4″ top and 7″ bottom with a 3/4″ dowel center.

Start by cutting the disks. I have a bandsaw and made a circle cutting jig inspired by one I saw on youtube. You can use a jigsaw, if that is what you have. Easiest on a bandsaw to cut out square blanks to start. With a jigsaw, cut to the circle you have drawn. Mark the center of the circle to make it easier to drill the dowel hole.Circle Cutting Band SawCutting Disk on BandsawBandsaw circle cutting

Hopefully the edges are relatively smooth. Use sandpaper to get them smoother. Sand the dowel too.  To round over the edges I used a 1/4″ round over bit in a router mounted in a table. Rounding over both sides. Sand both faces.

Router TableIMG_1351IMG_1353

Measure the diameter of the dowel you have. Sometimes they vary. Drill a hole for a snug fit. I used a Forstner bit to make a smooth bottomed hole half way through. You can drill all the way through using a spade bit (cheaper).  I finished them using water based polyurethane taking care not to get it in the holes. Apply the finish to the dowel before cutting it up.

Bases and tops for hat standIMG_1354

Cut the dowel to the lengths you need. I found a friction fit worked fine. Put your hat on the stand. Smile, because the brim of your fedora is protected.

Hatstand done